Guide · Homeowners · 4 min read · Updated 17 November 2026
Loft and Eaves Dressing Rooms: Design, Costs and Regulations
Short answer
A loft or eaves dressing room uses bespoke units cut to follow sloping ceilings, with full-height hanging where headroom allows and drawers, shelves or pull-outs under the eaves. It typically costs £7,000–£20,000 for the fitted furniture. The furniture itself does not need approval, but converting a loft into a habitable room requires Building Regulations approval for structure, fire safety and stairs.
Why lofts suit dressing rooms
Lofts and rooms with sloping ceilings are hard to furnish with standard wardrobes, which are designed for square rooms with full height. Bespoke units can follow every angle, turning awkward space into useful storage. Many loft bedrooms have eaves on one or both sides that are wasted with freestanding furniture but perfect for drawers and shoe storage.
A loft dressing room can also free up space on the floor below, and in some homes it creates a master suite with bedroom, dressing area and shower room on the top floor.
Designing around slopes
The key is to place each type of storage where the height suits it. Full-height hanging goes where the ceiling is highest, usually towards the centre of the room or under a dormer. Double hanging fits where there is a bit less height. Drawers, shelves and shoe storage go under the lower parts of the slope. Deep pull-out units on runners make the very back of the eaves usable.
Doors on sloping units can be angled to follow the ceiling line, which looks neat but costs more. Alternatively, a vertical knee wall can be built with square doors, leaving a small void behind for cables or rarely used items.
| Headroom | Best storage |
|---|---|
| Over about 1.8m | Long hanging, full-height doors |
| About 1.2m to 1.8m | Double hanging, shelves |
| Under about 1.2m | Drawers, shoe storage, pull-outs |
| Eaves void | Deep pull-outs or access hatches |
Costs
A loft or eaves dressing room typically costs £7,000–£20,000 for the bespoke furniture, depending on the amount of cabinetry, how many angled doors and cut panels are needed, and the finishes chosen. Units cut and scribed to rafters and walls take more design and fitting time than square units.
This is separate from the cost of converting the loft itself, which is a much bigger project involving structure, insulation, windows, stairs and fire safety.
- Amount of cabinetry and number of angled sections.
- Angled doors versus square doors on a knee wall.
- Finishes and internal fittings.
- Lighting and electrical work.
- Access for delivering units into the loft.
Building Regulations
Converting a loft to create a dressing room requires Building Regulations approval for structure, fire safety and stairs, even if the fitted furniture itself does not. A loft used as a dressing room is treated as part of the habitable space, so it needs a safe stair, adequate structure for the extra load, insulation and fire safety measures such as protected escape routes and smoke alarms where required.
If your loft is already converted with approval, fitting bespoke dressing room furniture does not need further approval. If it is boarded storage space without approval, check with building control before using it as a dressing room. Electrical work for lighting must be done to BS 7671, and some new circuits are notifiable under Part P.
Lighting and ventilation
Lofts can be dim, especially away from roof windows. LED lighting in rails, shelves and drawers makes a big difference, along with ceiling downlights or spotlights angled to the slopes. Roof windows give good natural light, but avoid placing clothes where direct sunlight will fade them.
Lofts can get warm in summer and cold in winter. Good insulation and ventilation help protect clothes from heat, damp and moths. Units should not be sealed tight against cold external walls, as this can cause condensation behind them; designers often leave a small ventilated gap.
- LED lighting inside units.
- Downlights or spots angled to slopes.
- Avoid direct sunlight on clothes.
- Ventilated gap behind units on cold walls.
Access and installation
Getting units into a loft can be tricky, especially with narrow or winding stairs. Bespoke makers often build units in smaller sections and assemble them in the room. Tell the designer about stair width, turns and headroom at the top of the stairs so they can plan the build. Installation of a loft dressing room typically takes two to four days.
Measuring a loft takes extra care. Rafters are rarely perfectly straight or evenly spaced, and the angle of the slope can change slightly along the room. A good designer takes detailed measurements, often making templates for the angled sections, so panels can be cut to follow the ceiling closely and scribed on site for a tight finish.
Dormers, roof windows and chimneys
Many lofts have dormers, roof windows or chimney breasts that break up the walls. A dormer often gives the best full-height space in the room, making it a good place for long hanging or a dressing table facing the window. Roof windows bring in light but take wall space, so units are usually designed to stop below or around them, leaving the window clear to open.
Chimney breasts create alcoves either side that suit fitted hanging or shelving. If a chimney is still in use from below, keep units clear of any hot surfaces and follow the designer's advice on spacing. In lofts with exposed purlins or beams, units can be notched around them or set in front with a scribed filler, depending on the look you want.
- Use dormers for long hanging or a dressing table.
- Keep roof windows clear to open.
- Fit alcoves beside chimney breasts.
- Notch or scribe units around beams and purlins.
Questions people also ask
Can you put a dressing room in a loft?
Yes, lofts make excellent dressing rooms. Bespoke units are cut to follow sloping ceilings, with full-height hanging where headroom allows and drawers or pull-outs under eaves. The loft conversion itself needs Building Regulations approval for structure, fire safety and stairs, but the fitted furniture does not.
How much does a loft dressing room cost?
Bespoke dressing room furniture for a loft or eaves space typically costs £7,000–£20,000, depending on the amount of cabinetry, angled sections, finishes and lighting. This is separate from the cost of converting the loft itself, which involves structural, insulation and fire safety work.
What storage works best under eaves?
Under eaves, where headroom is low, drawers, shoe shelves and deep pull-out units work best. Pull-outs on runners make the back of the eaves usable. Hanging should go where the ceiling is highest. A vertical knee wall with square doors is a simpler alternative to angled doors.
Written and checked by the Bespoke Dressing Rooms team. Read our editorial policy.
More guides
How Much Does a Bespoke Dressing Room Cost in the UK?
A bespoke dressing room in the UK typically costs £6,000–£15,000 for a walk-in wardrobe with units on two or three walls, and £10,000–£30,000 for a…
Dressing Room Dimensions and Layout: How Much Space Do You Need?
Hanging wardrobes need to be around 60cm deep, with a clear walkway of at least 90cm in front. A room around 2m wide can take units on one side, and…
Dressing Room Lighting: LED Rails, Shelf Lights and Mirrors
Good dressing room lighting layers ceiling lights for general light with LED strips in hanging rails, shelves and drawers, plus bright, even light at…
Converting a Spare Room Into a Dressing Room: A Complete Guide
Converting a spare room into a dressing room typically costs £10,000–£30,000 for a full bespoke fit-out with units, dressing table, island option and…
Get a free bespoke dressing rooms quote
Tell us what you need and we'll come back with a clear price.
Request a quote